Total MoldMaking Business Index for September 2013

Article From: MoldMaking Technology,

Posted on: 11/20/2013



Overall, the trend in the activity levels for U.S. manufacturers continues to exceed expectations. In fact, if not for the auto sector and the residential construction sector, the U.S. economy would most likely have entered a recession in 2013. The best way to describe it is that manufacturing is holding up pretty well this year in spite of the persistent headwinds caused by lower consumer confidence and weaker global demand. The trend in our MoldMaking Business Index so far this year has been gradually downward, but just the opposite is true for many of the other manufacturing sector indicators in recent months. There is little to suggest that the recovery will accelerate in the near-term, but the underlying fundamentals continue to strengthen. House prices are rising, interest rates remain low and the employment data are steadily improving. On the consumer side, there is a lot of pent-up demand for all kinds of durable goods products, while on the business side there remains a huge amount of cash sitting on the sidelines looking for a good reason to be invested. All of the ingredients are in place for a more rapid pace of economic expansion in 2014. Congress may yet screw this up, but at least for now, the economic fundamentals are encouraging.

Our latest survey of the North American moldmaking industry indicates that overall activity levels declined for the third straight month in September when compared with the previous month, but the rate of decline is decelerating. The MoldMaking Business Index for September 2013 is 48.2 (a value less than 50.0 indicates a decrease in business levels for the month). The latest index value is a 3.5-point increase from the August value of 46.1, and it is a 0.9-point decrease from the 49.1 value posted in September 2012.

The index recovered much of the deeper drop-off from last month, but not all of it. If we look at the bigger picture, the overall trend all year for the MoldMaking Business Index has been flat-to-down, and the September reading continued this trend.

Yet again, there is some consolation in the fact that the latest reading for our MoldMaking Business Index is a contrast to many of the major indicators that measure overall manufacturing levels in the U.S. The ISM Manufacturing Index in September posted its highest mark since 2011, coming in at a heartening 56.2. Demand for autos remained strong in September. The upward trends in residential construction and real estate data decelerated a bit recently, but both are still quite strong when compared with last year.

The biggest threat to the current economic recovery does not come from any of the economic fundamentals at the present time, but rather from Congress. As I write this, the Federal government is in shutdown, and a vote on the nation’s debt ceiling is just a few days away. If these two issues are not resolved in an expeditious and somewhat graceful manner, the effects on the U.S. economy will be dire. If, on the other hand, Congress and the President can quickly get us past this debacle, then the pace of economic expansion will accelerate through at least the end of 2014.

Taking a closer look at the categories that comprise our index, the new orders component was 48.4 in the latest month. This is significantly higher than August’s reading of 43.6, and it now appears this weak August figure was largely due to planned shutdowns and vacations, and less because of weakening market demand.

The production subindex of 52.0 indicates that work levels increased, as they have for most of the year. With new orders lower and production levels up, we should expect a decline in backlogs. And that is what happened, as the backlogs subindex eased back to 40.0. The employment component was exactly 50.0, which means that moldmakers’ payrolls were steady.

The prices received in the moldmaking sector were modestly lower in September, with a subindex of 48.8. The upward momentum in materials prices accelerated a bit, coming in at 61.8. Supplier delivery times resumed their recent trend of gradual expansion, posting a 53.6 in September. The pace of decline in offshore orders was little changed, with the exports subindex coming in at 45.3.

The MoldMaking Business Index is based on a monthly survey of subscribers to MoldMaking Technology magazine. Using the data from this survey, Gardner Research calculates a diffusion index based on 50.0. A value of more than 50.0 for the index indicates that business activity expanded when compared with the previous month, and a value of less than 50.0 means that business levels declined.

Comments are reviewed by moderators before they appear to ensure they meet Products Finishing’s submission guidelines.
blog comments powered by Disqus

Suppliers | Products | Experts | News | Articles | Calendar | Process Zones

The Voice of the Finishing Industry Since 1936 Copyright © Gardner Business Media, Inc. 2016

Subscribe | Advertise | Contact Us | All Rights Reserved