[ Log On ]

Deep Links

Extend Cleaning Bath Life with Ultrafiltration -
Over time, aqueous parts washer cleaning baths build-up with oil and sludge, exhausting the cleaning performance of the detergent. Quite often the solution to the problem is, dump and recharge. With a PROCECO Ultrafiltration system, cleaning bath life can be extended six-fold, and detergent costs can be cut in half. Our fully integrated Ultrafiltration (UF) systems are designed to operate unattended, and require little maintenance.
PROCECO Spray Cabinet Parts Washers -
PROCECO spray cabinet washers combine pressure, heat, and an aqueous cleaning solution to clean and degrease components to your specifications within minutes. Available in different models to suit your parts cleaning needs, your cabinet parts washer can be designed in single- or multi-stage configurations and customized by choosing from over 40 available options. Features such as digital temperature controllers and 7-day timers are standard on all PROCECO systems.
PROCECO Slurry Blasting (Wet Blasting) Cleaning Systems -
PROCECO slurry blasting uses a blast wheel to accelerate and discharge the abrasive slurry at high velocity and in a controlled pattern to mechanically remove oxides, scale, paint, carbon deposits, oil, and grease from a metal surface. PROCECO slurry blasting (also known as wet blasting) is the ultimate metal component blast cleaning process.
PROCECO In-Line, Conveyor Parts Washers -
PROCECO conveyor parts washers are ideal for cleaning parts automatically in a continuous process. Based on a modular approach, conveyor parts washers are designed in single- and multi-stage configurations to clean parts and perform any additional processes if required. Each PROCECO parts washer can be easily customized by adding various pre-engineered options to enhance system performance and meet all of your cleaning specifications and requirements.
PROCECO Spray -Immersion Washer for Precision Cleaning of Parts in Baskets -
The TYPHOON^®-SI, a PROCECO spray and immersion parts washer, is ideal for precision cleaning of machined components . The SI washer can handle a wide variety of complex small- or medium-size parts using standard baskets (two or four) or custom-engineered PROCECO holding fixtures. The SI parts washer comes complete with fully recirculated, aqueous immersion wash and rinse. Basket rotation during immersion and power-spraying ensures precision cleaning and complete removal of contamination

As seen in PF

Proceco UF System Extends Cleaning Solution Bath Life
The Proceco UF ultrafiltration system is designed to remove emulsified oils from parts cleaning solution baths, extending solution life up to six times, the company says.
Mechanical Vapor Recompression Evaporation
MVRE is underutilized in the treatment of industrial wastewaters that are typical of metal fabricating and finishing industries. Increasing energy costs, rapidly decreasing freshwater resources, and growing sensitivity towards the environmental impact of industrial management practices are the driving forces in the development of more sustainable technology.
Parts Cleaning Using a Blasting Wheel
Proceco’s new slurry blasting parts cleaning technology, also known as wet blasting, uses a rotary wheel to discharge a mixture of hot cleaning solution and abrasive media.
Conveyor Washer with Continuous Flow Cleaning
Proceco’s MB-S is an in-line belt conveyor aqueous washer from the company’s Typhoon series.
Heavy-Duty Turntable Cabinet Spray Washers
Proceco’s Typhoon HD turntable spray washers are designed to clean large parts placed directly on a retractable turntable or batches of small workpieces loaded in baskets.
Parts Cleaner System
Company features the TYPHOON® SI, a compact and ergonomic cleaning parts system designed to handle a variety of parts inside standard baskets or in custom-engineered fixtures.

Proceco Ltd.

Contact Information

Please visit: Proceco Ltd.

Mailing Address:
7300 Tellier St.
Montreal, QC H1N 3T7 CA

Phone: 514-254-8494
Toll-Free: 800-978-6677
Fax: 514-254-8184

A Special Message from Proceco Ltd.

PROCECO Integrated Cleaning Solutions

PROCECO Éco-Smart Mechanical Vapor-Recompression (MVR) Evaporator	Wastewater Treatment Systems Install a PROCECO Éco-Smart^® Mechanical Vapor-Recompression (MVR) evaporator to reduce up to 98% of your process wastewater and to operate in a closed loop. The Éco‑Smart^® uses vacuum distillation technology to reclaim up to 98% of water from surface treatment rinse waters, cleaning solution baths, metalworking fluids, and concentrates from ultrafiltration. The system produces a clean distillate that can be re-used as make-up water while the contaminants are concentrated in sludge to be disposed. The Éco-Smart^® does not use electric, gas, or steam heat sources to evaporate the wastewater. Based on the average US electrical cost of 0.07$ Kwh, it costs less than 2¢ to treat 1 gallon of wastewater. The system runs unattended and requires little maintenance. The Éco-Smart^®MVR evaporator is an ideal solution to minimize your environmental footprint and reduce your operational costs.

PROCECO ADT Immersion Automated Tank Lines	Surface Treatment Immersion Tank Lines PROCECO's ADT immersion tank lines are automated multi-stage systems designed for metal surface treatment, such as anodizing, pickling and phosphating. ADT systems can also be designed for aqueous parts degreasing and precision cleaning processes. Our immersion systems offer automation, process control, dynamic scheduling, and automatic part transfer hoists to meet your exact needs. In addition, additional features such as ultrasonics, agitation, turbulation rotation, and spray processes can be integrated with any immersion tank line models. Each immersion system is custom engineered for specific processes and workpieces. PROCECO provides complete solutions from initial concept to turnkey installation.

PROCECO Aqueous Parts Washers	Aqueous Parts Washers PROCECO designs and manufactures a complete selection of parts washers such as: turntable spray cabinets, belt conveyor lines, monorail systems, rotary and spray-immersion washers. Using a recirculated, hot detergent solution, PROCECO's parts washers remove oils, grease, chips, dirt, coolants and other contaminants for parts pre-treatment. PROCECO washers can be designed to meet your cleaning requirements and are available in single or multi-stage configurations, with steel or stainless-steel construction, and a wide selection of options.

Company Profile

PROCECO designs and manufactures a wide range of industrial aqueous parts washers, surface treatment equipment, and high-pressure water deburring systems.

To complement parts cleaning and surface treatment systems, PROCECO also manufactures mechanical vapor recompression evaporators to treat and recycle up to 98% of process wastewater issued from parts cleaning, surface treatment, and FPI rinse processes.

Since 1975, PROCECO has supplied over 6700 systems to more than 50 countries worldwide for the General Manufacturing, Aerospace, Automotive, Rail & Transit, and Heavy Machinery Industries. PROCECO provides cleaning systems for parts manufacturing as well as for maintenance, repair, and overhaul processes.

ISO 9001:2008 and ISO 14001 Certified.